Results 1 to 6 of 6

Thread: Sunray4/SR4 sim2 -Tutorials

  1. #1

    korn's Avatar
    Join Date
    Dec 2010
    Location
    SatDreamGr
    Posts
    51,784
    Rep Power
    2484984

    Sunray4/SR4 sim2 -Tutorials

    Sunray4/SR4 sim2 is next model for sim2 clone boxes -specifications





















    Newest DVB receiver Sunray4 DM800 se SR4—WIFI, 300M WLAN supported
    Tuner: Three-in-One DVB-S2/C/T, Tuner can be used at the same time.
    Powerful receiver for digital TV and Radio programs.
    Main features are a 400 MHz processor the DVB receiver 800 HD se supports the Linux TV API

    Have a look to HighDefinition TV on your DVB receiver

    •10/100MBit compatible Ethernet Interface
    •HDMI connector
    •plug & play Tuner
    •colored OLED display
    •plug & play slot for an internal 2,5" SATA hard disk

    Technical Features

    • 400 MHz MIPS Processor
    • Enigma 2, Linux Operating System
    • WIFI: 300Mbps Wireless LAN
    • colored OLED - Display
    • MPEG-2 / H.264 Hardware decoding
    • Tuner: DVB-S2,DVB-C, DVB-T
    • Tuner Module, Plug&Play
    • 2 x Smartcard-Reader (Dreamcrypt CA)
    • Mini USB for Service and software update
    • 10/100Mbit Ethernet Interface
    • 1 x Scart (RGB, FBAS or S-Video)
    • HDMI
    • 3 x USB 2.0 ( A USB in front panel) (e.g keyboard)
    • analog modem
    • S/PDIF Interface for digital bit stream out (AC-3)
    • 64 MByte Flash, 256 MByte RAM
    • SATA - for internal HDD 2,5“
    • unlimited channel lists for TV/Radio
    • channel-change time < 1 second
    • automatic service scan
    • directly bouquet-lists
    • EPG (electronic program guide)
    • multiple LNB-Switching control (supports DiSEqC)
    • OSD in many languages and skin-support
    • Videotext Decoder
    • extern 12V power supply
    • Learning remote control
    DVB receiver 800 HD se technical data
    DBS-Tuner mit DVB-S2:
    Frequency Range 950 .... 2150 MHz
    Demodulation DVB-S (QPSK); DVB-S2 (8PSK,QPSK)
    Symbol rate DVB-S: 2 ... 45 Mbaud/s, SCPC/ MCPC
    DVB-S2: 10 – 31 Mbaud/s (8PSK) , 10 –30 Mbaud/s (QPSK)

    Video decoder:
    Video Compression MPEG-2 and MPEG-1 compatible, H.264
    Video Formats 4:3 / 16:9
    Letterbox for 4:3 TV-Device

    Audio decoder:
    Audiokompression MPEG-1 & MPEG-2 Layer I and II, MP3
    Audio Mode Dual (main/sub), Stereo
    Frequency: 32 kHz, 44.1 kHz, 48 kHz, 16 kHz, 22.05 kHz, 24 kHz

    Output analog:
    Output Level L/R 0,5 Vss on 600 Ohm
    THD > 60 dB (1 kHz)
    Crosstalk < -65 dB

    Output digital:
    Output Level 0,5 Vss on 75 Ohm
    Sampled Data Filtering 32 kHz, 44.1 kHz, 48 kHz
    S/PDIF-Output optical, Toslink

    Ausgang Video:
    Ausgangspegel FBAS 1 Vss +/- 0.3 dB an 75 Ohm

    Video parameter:
    Input Level FBAS 1 Vss +/- 0.3 dB on 75 Ohm
    Teletext filter in conformity with ETS 300 472 Standard

    TV-Scart:
    Output: FBAS, RGB, S-Video

    Mini USB service connector:
    Function: Update of Firmware

    Ethernet:
    10/100 MBit compatible interface
    Function: Update of Firmware

    Analoge modem:
    analoge modem for Internet connection

    SATA Interface:
    for internal 2,5" HDD

    USB
    2 x USB 2.0

    LNB power and polarisation per tuner:
    LNB Current 500mA max.; short-circuit-protected
    LNB Voltage vertical < 14V no load, > 11,5V at 400mA
    LNB Voltage horizontal < 20V no load, > 17,3V at 400mA

    Count of active satellite position:
    DiSEqC 1.0/1.1/1.2 and USALS (Rotor Control)

    Power consumption:
    < 15W at 12V

    External PSU
    Input:
    110-240V AC / 50-60Hz / 0,6A
    Output:
    12V = / 3,0A

    Physical specification:
    Ambient Temperature +15°C...+35°C
    Humidity < 80%
    Size (W x D x H): 225 mm x 145 mm x 52 mm
    Weight: 940 g without HDD

    from sat-planet
    special thanks to oys

  2. #2

    korn's Avatar
    Join Date
    Dec 2010
    Location
    SatDreamGr
    Posts
    51,784
    Rep Power
    2484984

    Απ: Sunray4/SR4 sim2 -Tutorials

    Mini Flashup _ How to on Dm800Se







    Mini Flashup

    used mainly for managing the error ca not found without using dreamup

    If you think these two solutions are hard and complex, there is a new special solution for DM800SE.

    You know, one of feature of DM800SE is that it supports DVB-S, DVB-C, and DVB-T in one device. But, another feature of it is it has a Mini flashup Button. Whatever software you want flash into the Dreambox, How ever your Dreambox become, a easy Mini flashup button make your Dreambox reset as a new one.

    Steps:
    Pls make sure your Dreambox is DM800SE with a Mini Flashup button in the back, and it is active (make sure the Pin, below the Tuner, is plug)
    Connect the network cable, press and hold the Mini Flashup button, power on your DM800SE, then it will go into the page of flashing
    Repeat Resolution as per this thread http://dreamoem.com/showthread.php?2...Up-and-Browser to update firmware

    Tutorial prepared by Joedenoble
    from
    sat4fun

  3. #3

    korn's Avatar
    Join Date
    Dec 2010
    Location
    SatDreamGr
    Posts
    51,784
    Rep Power
    2484984

    Απ: Sunray4/SR4 sim2 -Tutorials

    How to use dvb C and T Tuners in Sunray/dm800se- sr4







    Load latest image for it here SIM2 images for Sunray4/SR4

    by Joedenoble from sat4fun

  4. #4

    korn's Avatar
    Join Date
    Dec 2010
    Location
    SatDreamGr
    Posts
    51,784
    Rep Power
    2484984

    Απ: Sunray4/SR4 sim2 -Tutorials

    DVB-C Scanning With Triple Tuner Sim2 DM800SE SR4


    First some back ground info on the Triple Tuner Config Setup.

    Despite the pictures you may have seen posted on various forums the triple tuner does not show up in the tuner config as 3 separate tuners it will only show up as a single DVBS Tuner at the moment, that does not stop you using each tuner format though S,C ot T. You can also scan on any image you don't need anything special tested on Sunray & Nemesis images.

    Before you start to scan for DVBC channels you'll need to find out the Channel Frequencies and Symbol rate for your Country/Area.

    Once you have that you can start to set up the tuner configuration.

    On your remote Menu-Setup-Service Searching-Tuner Config

    1. Setup the tuner as per the screen shot.


    On the pic you'll see it says DVBC at the Satellite position that's because i did my own edit on the satellite.xml with my area details but as we are manually scanning just select any Satellite position it does not matter.

    2. Now exit the tuner config and select the manual scan option and set up as per the pic.

    The main thing you have to remember here is the frequencies you enter needs to have a 01 in front of it. So if a frequency for your area is 643.000 you loose the 000 from the end and put a 01 in front of the 643 so you end up with 01634 in the frequency entry. For the symbol rate you need in most cases a zero in front so 6667 will be entered as 06667.

    Once thats setup up with those parameters press OK to scan





    Now repeat for all your other frequencies.

    Ive not tried a automatic scan but i guess you could if you prepare the satellite.xml with all your frequency details to scan with.

    Hope this helps you.

    By Ferret sat4fun

  5. #5

    korn's Avatar
    Join Date
    Dec 2010
    Location
    SatDreamGr
    Posts
    51,784
    Rep Power
    2484984

    Απ: Sunray4/SR4 sim2 -Tutorials

    how to use learning type remote controller for Sunray4/SR4







    how to use learning type remote controller for Sunray4/SR4(chinese).
    Operation steps:

    1 select TV mode, press the learning type remote controller [ SHIFT ] on the key, approximately 3 Seconds after the TV indicator light on, enter [ learning ] mode.

    2 press to a learning remote controller want to learn the key, the indicator slow flicker, said into the [learning mode] of waiting to receive a learning signal state.

    3 will be a learning remote controller receiving tube on the original remote transmitting tube, between 2 to 3cm . The original remote control to learn button once, then learning

    Remote indicating lamp by slow flicker for flash 3 times after Long light, said a key learning success.

    4 , other learning button only needs to repeat the above 2, 3 step.

    5 after the completion learning, then press [ SHIFT ] to save and exit learning state.

    6 into the state of learning, interval 15S learning no press input signal input, remote control lights automatic

    Extinguished, leaving [ learning mode ] and automatically save.

    7 the same key to learning ,then save the last the code value.

    The key to studying as follows:

    include power, digital key 0-10,

    The volume +, -, BOUQUET + volume,

    The BOUQUET and TV keys

    Press" DVB" and" TV ( SHIFT )" for mode conversion.

  6. #6

    korn's Avatar
    Join Date
    Dec 2010
    Location
    SatDreamGr
    Posts
    51,784
    Rep Power
    2484984

    Απ: Sunray4/SR4 sim2 -Tutorials

    SUNRAY SE SR4 configurazione tuner OK








    Finally finished

    I put the steps to be taken to configure the tuner for the satellite and DTT, configured with a dual-feed hotbird, astra and DTT.
    Download and install the dual-feed setting of 13-19 Vhannibal
    Satellite.xml overwrite the file from etc / tuxbox with the file attached to the end of the post
    restart Enigma

    Go Menu' - Configuration - Channel Search - Configuration Tuner

    Choose the mode 'Advanced Configuration

    and configure the 3 "satellites" HOTBIRD-ASTRA AND DVB-T Europe
    in sequence.


    Finalmente finito..:icon_thumleft:

    Metto la procedura da adottare per configurare il tuner per il sat e dtt, configurato con un dual-feed hotbird ,astra e il dtt.
    Scaricare e installare i setting dual-feed 13-19 di Vhannibal
    Sovrascrivere il file satellite.xml da etc/tuxbox con il file allegato alla fine del post
    Riavviare Enigma

    Andare in Menu'--Configurazione--Ricerca canali--Configurazione tuner

    Scegliere la modalita' di configurazione Avanzato

    e configurare i 3 "satelliti" HOTBIRD-ASTRA E DVB-T Europe
    in seguenza.
    [IMG]http://img3.**************/img3/7921/foto1zg.jpg[/IMG]

    hotbird..dare ok e proseguire
    [IMG]http://img337.**************/img337/1755/foto2jv.jpg[/IMG]

    astra..dare ok e proseguire


    [IMG]http://img534.**************/img534/2976/foto3tv.jpg[/IMG]

    DVB-T Europe..dare ok e uscire
    Bene,ora avete configurato i 3 "satelliti"

    Ora andiamo ad effettuare la ricerca canali del dtt:
    Posizionarsi su Ricerca manuale
    [IMG]http://img198.**************/img198/544/foto4pw.jpg[/IMG]


    Configurare il modo di scansione manuale:
    [IMG]http://img29.**************/img29/5847/foto5az.jpg[/IMG]

    OK,inizia la scansione del DTT
    [IMG]http://img580.**************/img580/6447/foto6x.jpg[/IMG]

    Wait for it to finish scanning.
    end
    Aspettare che finisca la scansione.
    Fine

    Thanks to arthur
    Attached Files Attached Files

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. MAG-250 Tutorials
    By sat gr in forum MAG-infomir Media Players
    Replies: 4
    Last Post: 11-04-14, 21:33
  2. DM800SE Clone Images Sunray4/SR4 sim2.10 ssl84b
    By sat gr in forum Images DM800SE
    Replies: 172
    Last Post: 05-03-14, 16:43
  3. Ποιά η γνώμη σας για τον Κινέζικο Sunray4/SR4?
    By woodstock69 in forum ..Περί Dreambox Enigma2
    Replies: 0
    Last Post: 22-01-12, 13:04
  4. Sunray4/SR4 sim2 is next model for sim2 clone boxes
    By sat gr in forum ..Περί Dreambox Enigma2
    Replies: 0
    Last Post: 31-12-11, 07:33
  5. Tutorials / FAQ for Azbox HD E2
    By djdiageo in forum Περί AZBox HD
    Replies: 1
    Last Post: 12-01-11, 12:07

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •