Page 2 of 2 FirstFirst 12
Results 11 to 13 of 13

Thread: Technisat SkyStar HD usb on SF4008

  1. #11

    athoik's Avatar
    Join Date
    Sep 2012
    Location
    Earth
    Posts
    10,758
    Rep Power
    5927763

    Απ: Technisat SkyStar HD usb on SF4008

    Damn, I was so sure that problem was this patch!

    There two more patches, related with DMA but no idea if something will change.

    Previous state was broken and current too.
    Member SatDreamGr Projects

    Wavefield T90: 0.8W - 1.9E - 4.8E - 13E - 16E - 19.2E - 23E - 26E - 33E - 39E - 42E - 45E on EMP Centauri DiseqC 16/1
    Unamed: 13E Quattro - 9E Quattro on IKUSI MS-0916

  2. #12

    jpuigs's Avatar
    Join Date
    Dec 2017
    Location
    Barcelona
    Age
    50
    Posts
    255
    Rep Power
    68921

    Re: Technisat SkyStar HD usb on SF4008

    I've uninstalled it, reboot, and installed again....

    Code:
    root@sf4008:~# opkg install enigma2-plugin-drivers-dvb-usb-technisat-skystar
    Installing firmware-dvb-usb-technisat-skystar (1.1+git293+8dfa20f) on root.
    Downloading http://188.165.252.42/feeds/satdreamgr-6/all/firmware-dvb-usb-technisat-skystar_1.1+git293+8dfa20f-r0_all.ipk.
    Installing kernel-module-dvb-usb-technisat-usb2 (4.1.37) on root.
    Downloading http://188.165.252.42/feeds/satdreamgr-6/sf4008/kernel-module-dvb-usb-technisat-usb2_4.1.37-r10_sf4008.ipk.
    Installing kernel-module-stv090x (4.1.37) on root.
    Downloading http://188.165.252.42/feeds/satdreamgr-6/sf4008/kernel-module-stv090x_4.1.37-r10_sf4008.ipk.
    Installing kernel-module-stv6110x (4.1.37) on root.
    Downloading http://188.165.252.42/feeds/satdreamgr-6/sf4008/kernel-module-stv6110x_4.1.37-r10_sf4008.ipk.
    Installing enigma2-plugin-drivers-dvb-usb-technisat-skystar (1.0) on root.
    Downloading http://188.165.252.42/feeds/satdreamgr-6/all/enigma2-plugin-drivers-dvb-usb-technisat-skystar_1.0-r0_all.ipk.
    Configuring kernel-module-stv090x.
    Configuring firmware-dvb-usb-technisat-skystar.
    Configuring kernel-module-dvb-usb-technisat-usb2.
    Configuring kernel-module-stv6110x.
    Configuring enigma2-plugin-drivers-dvb-usb-technisat-skystar.
    root@sf4008:~#
    But same results.

    If I add these modules to /etc/modules-load.d/_sf4008.conf

    dvb-usb
    dvb-usb-technisat-usb2
    stv6110x
    stv090x

    Code:
    root@sf4008:~# lsmod                                   
    Module                  Size  Used by                  
    ipv6                  281810  47                       
    dvb_usb_technisat_usb2     7736  0                     
    dvb_usb                14835  1 dvb_usb_technisat_usb2 
    stv090x                54453  0                        
    stv6110x                4137  0                        
    linuxtv              8822612  31
    dmesg shows:
    usbcore: registered new interface driver dvb_usb_technisat_usb2 when pluging in.
    But all other messages (Firmware.....) don't.

  3. #13

    jpuigs's Avatar
    Join Date
    Dec 2017
    Location
    Barcelona
    Age
    50
    Posts
    255
    Rep Power
    68921

    Re: Technisat SkyStar HD usb on SF4008

    I've uninstalled it, deleted all I added in the /etc/modules-load.d
    I've disconnected usb receiver from 7,5 v.
    I've connected it all again.....
    and now it detects it…..

    Code:
    usb 4-1.3: new high-speed USB device number 4 using ehci-brcm
    technisat-usb2: set alternate setting
    dvb-usb: found a 'Technisat SkyStar USB HD (DVB-S/S2)' in cold state, will try to load a firmware
    dvb-usb: downloading firmware from file 'dvb-usb-SkyStar_USB_HD_FW_v17_63.HEX.fw'
    usbcore: registered new interface driver dvb_usb_technisat_usb2
    usb 4-1.3: USB disconnect, device number 4
    dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
    usb 4-1.3: new high-speed USB device number 5 using ehci-brcm
    technisat-usb2: set alternate setting
    technisat-usb2: firmware version: 17.63
    dvb-usb: found a 'Technisat SkyStar USB HD (DVB-S/S2)' in warm state.
    dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
    DVB: registering new adapter (Technisat SkyStar USB HD (DVB-S/S2))
    dvb-usb: MAC address: 00:08:c9:f0:7b:9b
    stv6110x_attach: Attaching STV6110x
    technisat-usb2: i2c-error: 60 = 7
    usb 4-1.3: DVB: registering adapter 1 frontend 0 (Technisat SkyStar USB HD (DVB-S/S2))...
    IR keymap rc-technisat-usb2 not found
    Registered IR keymap rc-empty
    input: IR-receiver inside an USB DVB receiver as /devices/platform/rdb/f0470500.ehci_v2/usb4/4-1/4-1.3/rc/rc0/input1
    rc0: IR-receiver inside an USB DVB receiver as /devices/platform/rdb/f0470500.ehci_v2/usb4/4-1/4-1.3/rc/rc0
    dvb-usb: schedule remote query interval to 100 msecs.
    dvb-usb: Technisat SkyStar USB HD (DVB-S/S2) successfully initialized and connected.
    technisat-usb2: i2c-error: 68 = 64
    platform sf4008.0: DVB: registering adapter 0 frontend 24 (TechniSat USB device)...
    technisat-usb2: i2c-error: 68 = 64
    technisat-usb2: i2c-error: 68 = 64
    technisat-usb2: i2c-error: 68 = 64
    technisat-usb2: i2c-error: 68 = 64
    technisat-usb2: i2c-error: 68 = 65
    technisat-usb2: i2c-error: 68 = 65
    technisat-usb2: i2c-error: 60 = 64
    technisat-usb2: i2c-error: 68 = 65
    technisat-usb2: i2c-error: 68 = 65
    technisat-usb2: i2c-error: 60 = 64
    technisat-usb2: i2c-error: 68 = 65
    technisat-usb2: i2c-error: 68 = 65
    technisat-usb2: i2c-error: 60 = 64
    technisat-usb2: i2c-error: 68 = 65
    technisat-usb2: i2c-error: 68 = 65
    technisat-usb2: i2c-error: 60 = 64
    But it doesn't tune.
    Look at red text. 2 frontends ???
    I remember (when using OpenPli 4) that this USB box didn't work on ET10K.
    You told me to update to satdreamgr 5 , which had a newer kernel version, and these i2c errors dissapeared, and of course box worked fine.
    So, is this the same problem…. (kernel) ?
    Last edited by jpuigs; 31-01-19 at 12:30.

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Tutorial for T2-MI on SF4008?
    By Ferio12 in forum SatDreamGr Images Chat
    Replies: 7
    Last Post: 04-02-19, 18:51
  2. UDPXY on SF4008
    By jpuigs in forum SatDreamGr Images Chat
    Replies: 2
    Last Post: 05-12-18, 21:43
  3. Android app για τον SF4008
    By deepbluesky in forum SF4008
    Replies: 7
    Last Post: 01-06-18, 16:29
  4. TECHNISAT SKYSTAR HD2
    By tzav in forum Μικρές αγγελίες
    Replies: 1
    Last Post: 23-09-14, 18:35

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •