Damn, I was so sure that problem was this patch!
There two more patches, related with DMA but no idea if something will change.
Previous state was broken and current too.
Damn, I was so sure that problem was this patch!
There two more patches, related with DMA but no idea if something will change.
Previous state was broken and current too.
Member SatDreamGr Projects
Wavefield T90: 0.8W - 1.9E - 4.8E - 13E - 16E - 19.2E - 23E - 26E - 33E - 39E - 42E - 45E on EMP Centauri DiseqC 16/1
Unamed: 13E Quattro - 9E Quattro on IKUSI MS-0916
I've uninstalled it, reboot, and installed again....
But same results.Code:root@sf4008:~# opkg install enigma2-plugin-drivers-dvb-usb-technisat-skystar Installing firmware-dvb-usb-technisat-skystar (1.1+git293+8dfa20f) on root. Downloading http://188.165.252.42/feeds/satdreamgr-6/all/firmware-dvb-usb-technisat-skystar_1.1+git293+8dfa20f-r0_all.ipk. Installing kernel-module-dvb-usb-technisat-usb2 (4.1.37) on root. Downloading http://188.165.252.42/feeds/satdreamgr-6/sf4008/kernel-module-dvb-usb-technisat-usb2_4.1.37-r10_sf4008.ipk. Installing kernel-module-stv090x (4.1.37) on root. Downloading http://188.165.252.42/feeds/satdreamgr-6/sf4008/kernel-module-stv090x_4.1.37-r10_sf4008.ipk. Installing kernel-module-stv6110x (4.1.37) on root. Downloading http://188.165.252.42/feeds/satdreamgr-6/sf4008/kernel-module-stv6110x_4.1.37-r10_sf4008.ipk. Installing enigma2-plugin-drivers-dvb-usb-technisat-skystar (1.0) on root. Downloading http://188.165.252.42/feeds/satdreamgr-6/all/enigma2-plugin-drivers-dvb-usb-technisat-skystar_1.0-r0_all.ipk. Configuring kernel-module-stv090x. Configuring firmware-dvb-usb-technisat-skystar. Configuring kernel-module-dvb-usb-technisat-usb2. Configuring kernel-module-stv6110x. Configuring enigma2-plugin-drivers-dvb-usb-technisat-skystar. root@sf4008:~#
If I add these modules to /etc/modules-load.d/_sf4008.conf
dvb-usbstv6110x
dvb-usb-technisat-usb2
stv090x
dmesg shows:Code:root@sf4008:~# lsmod Module Size Used by ipv6 281810 47 dvb_usb_technisat_usb2 7736 0 dvb_usb 14835 1 dvb_usb_technisat_usb2 stv090x 54453 0 stv6110x 4137 0 linuxtv 8822612 31
usbcore: registered new interface driver dvb_usb_technisat_usb2 when pluging in.
But all other messages (Firmware.....) don't.
I've uninstalled it, deleted all I added in the /etc/modules-load.d
I've disconnected usb receiver from 7,5 v.
I've connected it all again.....
and now it detects it…..
But it doesn't tune.Code:usb 4-1.3: new high-speed USB device number 4 using ehci-brcm technisat-usb2: set alternate setting dvb-usb: found a 'Technisat SkyStar USB HD (DVB-S/S2)' in cold state, will try to load a firmware dvb-usb: downloading firmware from file 'dvb-usb-SkyStar_USB_HD_FW_v17_63.HEX.fw' usbcore: registered new interface driver dvb_usb_technisat_usb2 usb 4-1.3: USB disconnect, device number 4 dvb-usb: generic DVB-USB module successfully deinitialized and disconnected. usb 4-1.3: new high-speed USB device number 5 using ehci-brcm technisat-usb2: set alternate setting technisat-usb2: firmware version: 17.63 dvb-usb: found a 'Technisat SkyStar USB HD (DVB-S/S2)' in warm state. dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (Technisat SkyStar USB HD (DVB-S/S2)) dvb-usb: MAC address: 00:08:c9:f0:7b:9b stv6110x_attach: Attaching STV6110x technisat-usb2: i2c-error: 60 = 7 usb 4-1.3: DVB: registering adapter 1 frontend 0 (Technisat SkyStar USB HD (DVB-S/S2))... IR keymap rc-technisat-usb2 not found Registered IR keymap rc-empty input: IR-receiver inside an USB DVB receiver as /devices/platform/rdb/f0470500.ehci_v2/usb4/4-1/4-1.3/rc/rc0/input1 rc0: IR-receiver inside an USB DVB receiver as /devices/platform/rdb/f0470500.ehci_v2/usb4/4-1/4-1.3/rc/rc0 dvb-usb: schedule remote query interval to 100 msecs. dvb-usb: Technisat SkyStar USB HD (DVB-S/S2) successfully initialized and connected. technisat-usb2: i2c-error: 68 = 64 platform sf4008.0: DVB: registering adapter 0 frontend 24 (TechniSat USB device)... technisat-usb2: i2c-error: 68 = 64 technisat-usb2: i2c-error: 68 = 64 technisat-usb2: i2c-error: 68 = 64 technisat-usb2: i2c-error: 68 = 64 technisat-usb2: i2c-error: 68 = 65 technisat-usb2: i2c-error: 68 = 65 technisat-usb2: i2c-error: 60 = 64 technisat-usb2: i2c-error: 68 = 65 technisat-usb2: i2c-error: 68 = 65 technisat-usb2: i2c-error: 60 = 64 technisat-usb2: i2c-error: 68 = 65 technisat-usb2: i2c-error: 68 = 65 technisat-usb2: i2c-error: 60 = 64 technisat-usb2: i2c-error: 68 = 65 technisat-usb2: i2c-error: 68 = 65 technisat-usb2: i2c-error: 60 = 64
Look at red text. 2 frontends ???
I remember (when using OpenPli 4) that this USB box didn't work on ET10K.
You told me to update to satdreamgr 5 , which had a newer kernel version, and these i2c errors dissapeared, and of course box worked fine.
So, is this the same problem…. (kernel) ?
Last edited by jpuigs; 31-01-19 at 11:30.
There are currently 1 users browsing this thread. (0 members and 1 guests)