I can't make SkyStar USB tuner work on Octagon 4008
Code:
root@sf4008:~# opkg install enigma2-plugin-drivers-dvb-usb-technisat-skystar
Installing blindscan-s2 (1+git19+632830a) on root.
Downloading http://188.165.252.42/feeds/satdreamgr-6/armv7ahf-neon/blindscan-s2_1+git19+632830a-r0_armv7ahf-neon.ipk.
Installing firmware-dvb-usb-technisat-skystar (1.1+git292+25f936b) on root.
Downloading http://188.165.252.42/feeds/satdreamgr-6/all/firmware-dvb-usb-technisat-skystar_1.1+git292+25f936b-r0_all.ipk.
Installing kernel-module-dvb-usb-technisat-usb2 (4.1.37) on root.
Downloading http://188.165.252.42/feeds/satdreamgr-6/sf4008/kernel-module-dvb-usb-technisat-usb2_4.1.37-r9_sf4008.ipk.
Installing kernel-module-stv090x (4.1.37) on root.
Downloading http://188.165.252.42/feeds/satdreamgr-6/sf4008/kernel-module-stv090x_4.1.37-r9_sf4008.ipk.
Installing kernel-module-stv6110x (4.1.37) on root.
Downloading http://188.165.252.42/feeds/satdreamgr-6/sf4008/kernel-module-stv6110x_4.1.37-r9_sf4008.ipk.
Installing enigma2-plugin-drivers-dvb-usb-technisat-skystar (1.0) on root.
Downloading http://188.165.252.42/feeds/satdreamgr-6/all/enigma2-plugin-drivers-dvb-usb-technisat-skystar_1.0-r0_all.ipk.
Configuring kernel-module-stv090x.
Configuring blindscan-s2.
Configuring firmware-dvb-usb-technisat-skystar.
Configuring kernel-module-dvb-usb-technisat-usb2.
Configuring kernel-module-stv6110x.
Configuring enigma2-plugin-drivers-dvb-usb-technisat-skystar.
root@sf4008:~#
dmesg shows:
Code:
usb 4-1.1: new high-speed USB device number 3 using ehci-brcm
technisat-usb2: set alternate setting
technisat-usb2: firmware version: 17.63
dvb-usb: found a 'Technisat SkyStar USB HD (DVB-S/S2)' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
dvb-usb: Technisat SkyStar USB HD (DVB-S/S2) error while loading driver (-12)
usbcore: registered new interface driver dvb_usb_technisat_usb2
root@sf4008:~#
lsmod:
Code:
root@sf4008:~# lsmod
Module Size Used by
ipv6 281810 45
dvb_usb_technisat_usb2 7736 0
dvb_usb 14835 1 dvb_usb_technisat_usb2
linuxtv 8822612 38
root@sf4008:~#
If I add STV modules at /etc/modules-load.d/
Code:
root@sf4008:~# lsmod
Module Size Used by
ipv6 281810 45
stv6110x 4137 0
stv090x 54453 0
dvb_usb_technisat_usb2 7736 0
dvb_usb 14835 1 dvb_usb_technisat_usb2
linuxtv 8822612 38
root@sf4008:~#
but it still gives "dvb-usb: Technisat SkyStar USB HD (DVB-S/S2) error while loading driver (-12)"
Does anybody have any idea what's happening ??
This USB tuner works perfectly on old Xtrend ET10000