Trying to install WinTV SoloHD....

[jpuigs]

When I try to install winTV Solo HD USB stick…….

root@sf4008:~# opkg install enigma2-plugin-drivers-ct2-dvb-usb-pctv292e
enigma2-plugin-drivers-ct2-dvb-usb-pctv292e: unsatisfied recommendation for kernel-module-em28xx-rc
Installing kernel-module-em28xx (4.1.37) on root.
Downloading http://188.165.252.42/feeds/satdream...-r8_sf4008.ipk.
Installing kernel-module-em28xx-dvb (4.1.37) on root.
Downloading http://188.165.252.42/feeds/satdream...-r8_sf4008.ipk.
Installing enigma2-plugin-drivers-ct2-dvb-usb-pctv292e (1.0) on root.
Downloading http://188.165.252.42/feeds/satdream...1.0-r0_all.ipk.
Configuring kernel-module-em28xx.
Configuring kernel-module-em28xx-dvb.
Configuring enigma2-plugin-drivers-ct2-dvb-usb-pctv292e.
root@sf4008:~#


It seems that this package is missing.
Where Can I get it ?

[athoik]

It doesn't mention something on the dmesg after those packages installed?

The missing one seems like rc related, most probably should be enabled on kernel.

[jpuigs]

No.

bcmgenet f0b00000.ethernet: configuring instance for internal PHY
bcmgenet f0b00000.ethernet eth0: Link is Down
bcmgenet f0b00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
NET: Registered protocol family 10
usb 4-1.4: new high-speed USB device number 5 using ehci-brcm
root@sf4008:~#


Box doesn't detect it.
On ET 10K it Works OK, installing the same both packages, dvb-usb-em28xx and ct2-dvb-usb-pctv292e , but the difference I see is that on et10k kernel-module-em28xx-rc is installed too.


ET10K:

[68434.364000] usb 4-1: new high-speed USB device number 4 using ehci-brcm
[68434.484000] em28xx 4-1:1.0: New device HCW soloHD @ 480 Mbps (2040:0264, interface 0, class 0)
[68434.484000] em28xx 4-1:1.0: DVB interface 0 found: isoc
[68434.484000] em28xx 4-1:1.0: chip ID is em28178
[68436.434000] em28xx 4-1:1.0: EEPROM ID = 26 00 01 00, EEPROM hash = 0xcfe6c504
[68436.434000] em28xx 4-1:1.0: EEPROM info:
[68436.434000] em28xx 4-1:1.0: microcode start address = 0x0004, boot configuration = 0x01
[68436.441000] em28xx 4-1:1.0: AC97 audio (5 sample rates)
[68436.441000] em28xx 4-1:1.0: 500mA max power
[68436.441000] em28xx 4-1:1.0: Table at offset 0x27, strings=0x0e6a, 0x1888, 0x087e
[68436.442000] em28xx 4-1:1.0: Identified as PCTV tripleStick (292e) (card=94)
[68436.442000] em28xx 4-1:1.0: dvb set to isoc mode.
[68436.442000] em28xx 4-1:1.0: Binding DVB extension
[68436.463000] i2c i2c-11: Added multiplexed i2c bus 12
[68436.463000] si2168 11-0064: Silicon Labs Si2168-B40 successfully identified
[68436.463000] si2168 11-0064: firmware version: B 4.0.2
[68436.474000] si2157 12-0060: Silicon Labs Si2147/2148/2157/2158 successfully attached
[68436.474000] dvbdev: DVB: registering new adapter (4-1:1.0)
[68436.474000] em28xx 4-1:1.0: DVB: registering adapter 4 frontend 0 (Silicon Labs Si2168)...
[68436.477000] em28xx 4-1:1.0: DVB extension successfully initialized
[68436.477000] em28xx 4-1:1.0: Registering input extension
[68436.478000] Registered IR keymap rc-pinnacle-pctv-hd
[68436.478000] input: 4-1:1.0 IR as /devices/platform/ehci-brcm.3/usb4/4-1/4-1:1.0/rc/rc3/input9
[68436.479000] rc rc3: 4-1:1.0 IR as /devices/platform/ehci-brcm.3/usb4/4-1/4-1:1.0/rc/rc3
[68436.479000] em28xx 4-1:1.0: Input extension successfully initalized
root@et10000:~#

root@et10000:~# lsmod
Module                  Size  Used by
em28xx_rc               9236  0
si2157                  5077  1
si2168                  7064  1
em28xx_dvb             25315  0
em28xx                 67117  2 em28xx_rc,em28xx_dvb
tveeprom               10969  1 em28xx
ipv6                  417795  49
it913x                  4073  1
regmap_i2c              3144  1 it913x
af9033                 26955  1
dvb_usb_af9035         18641  2
dvb_usb_v2             14982  1 dvb_usb_af9035
stb6100                 5751  1
dvb_usb_tbsusb         23725  2
stv6110x                4931  1
stv090x                72445  2
dvb_usb_technisat_usb2     8982  2
dvb_usb                18154  2 dvb_usb_technisat_usb2,dvb_usb_tbsusb
dvb                  9054767  8
modloader2             33169  1 dvb
modloader              22463  0
tpm                     6717  3 modloader,dvb,modloader2
root@et10000:~#

[jpuigs]

It's not an SDG issue, on OpenAtv and OpenVix it doesn't work too.

[athoik]

Use online update: https://github.com/satdreamgr/meta-o...2d3b3511ad05d0

Then try to reinstall the package enigma2-plugin-drivers-ct2-dvb-usb-pctv292e

[jpuigs]

Thanks, but it doesn't work. Same results.
Now, the em28xx_rc module installs, but I see that that was not the problem.

[athoik]

Any difference in dmesg?

[jpuigs]

No. usb 4-1.4: new high-speed USB device number 5 using ehci-brcm , and that's all.

[jpuigs]

I got it working !!

root@sf4008:~# modprobe em28xx card=94
root@sf4008:~# echo "2040 0264" > /sys/bus/usb/drivers/em28xx/new_id

and restarting enigma2 to appear on device list.

https://tvheadend.org/boards/4/topic...#message-34272


Is it any way to automatize it ? (I mean not to be written each time I reboot receiver) ?

[athoik]

The standard way to add options in a module is to create a file /etc/modprobe.d/em28xx.conf and insert the following:

options em28xx card=94

The

echo "2040 0264" > /sys/bus/usb/drivers/em28xx/new_id

Can go in /usr/bin/enigma2_pre_start.sh (make it executable).