Printable View
Is it possible to add plugin options for selecting different command line,as probably easier than to change options in command line.
Options:
FM wide / RDS, FM narrow, AM narrow, LSB, USB minimum these options
Secondly to have choice for tuning step.
Let's say 100 kHz, 25 kHz, 10 kHz, 1 kHz minimum these options.
Secondly there is I think no need to limit the tuning frequency.
I have put 0 to 1.8 GHz
Rgd MX
Of course not to mention that it would be good to have a dynamic change of frequency without pressing OK button.
Etc Etc
I'm trying to spread interest in this project.
http://www.vuplus-community.net/boar...0/#post-226509
One more change for FM
cmd = "sleep 0.5 && rtl_fm -f %sM -M fm -l 0 -A std -s 171k -g 40 -F 9 -E deemp
If there are radio amateurs which use the RTL-SDR dongle
I was able to add a few more buttons for precise tuning frequency for SSB an CW
Of course it is possible to use for other modulations.
Now i can change Mhz ,kHz,10 kHz and 100 Hz freq step
Changed and added coding
self["actions"] = ActionMap(["SetupActions", "DirectionActions", "WizardActions", "ColorActions", "MenuActions", "ChannelSelectEPGActions" , "ChannelSelectBaseActions" ],
===========================
"nextBouquet": self.up1,
"prevBouquet": self.down1,
"nextMarker": self.up2,
"prevMarker": self.down2,
"up": self.up,
"down": self.down,
"left": self.left,
"right": self.right,
"ok": self.ok,
"upRepeated": self.up,
"downRepeated": self.down,
"leftRepeated": self.left,
"rightRepeated": self.right,
=========================
def up1(self):
self.freqChange(Decimal("0.0001"))
def down1(self):
self.freqChange(-Decimal("0.0001"))
def up2(self):
self.freqChange(Decimal("0.001"))
def down2(self):
self.freqChange(-Decimal("0.001"))
def up(self):
self.freqChange(Decimal("0.01"))
def down(self):
self.freqChange(-Decimal("0.01"))
def left(self):
self.freqChange(-Decimal("1"))
def right(self):
self.freqChange(Decimal("1"))
My changed py file and info you can download from
http://www.vuplus-community.net/boar...0/#post-226509
To emphasize I am not python and plugin coder.
Changes:
You can tune all frequency not only commercial FM
1.Direct frequency changes without using OK button
2.Yellow button you can choose between Wide FM (170 Khz) for commercial radio and Narrow FM (10 Khz) for amateur radio and other communication services taxi/marine communications/transport e.t.c
3. Some skin changes
4. added extra buttons to change the frequency
left/right change frequency by 1 Mhz
up/down change frequency by 10 Khz
Buttons < and > change frequency by 1 Khz (step by step)
Buttons channel + and - change frequency by 100 Hz (step by step)
Bugs
What we should look at.
Tuner sometimes out of sync.
Requires restart
@athoik @elbandido
can you help me with coding ?
I'd like to have a wide FM, Narow FM.Narrow AM, LSB and USB.
How to add another three command lines , and three new choice/options with a yellow button.
I know to configure command lines but I do not know python coding to add all this extras.
Rgd MX
=========================================================
this
if config.sdgradio.rds.value:
cmd = 1
else:
cmd=2
else:
cmd=3
else
cmd=4
....
...
and this
if config.sdgradio.rds.value:
self['key_yellow'].setText(_('....'))
else:
self['key_yellow'].setText(_('....'))
else
...
...
if config.sdgradio.rds.value:
self['key_yellow'] = Label(_('....'))
else:
self['key_yellow'] = Label(_('....'))
...
...
Rgd MX
I guess we need a dropdown list where mode can be selected.
FM
Narow FM
Narrow AM
LSB
USB
Yes this is what we need.
And more buttons to adjust the frequency.
I do not know if you saw my py file on the Black Hole forum.
I have added a couple of buttons to adjust the frequency.
What would be also nice to have but later
squelch button for noise canceling
and perhaps scanning if possible.
options
[-l squelch_level (default: 0/off)]
[-t squelch_delay (default: 10)]
+values will mute/scan, -values will exit
I undrestand that you used more buttons to change frequency with different step.
Should be fine to commit this one.