Dreambox V2 remote controls TV mode setup

Εψαχνα εψαχνα στο net αλλα πουθενα δεν εβρισκα, οδηγό για τα remote control των v2 dreambox στο πως προγραμματίζονται για να λειτουργούν σε TV mode.

Τον ανεβάζω εδω για όποιον τον χρειαστεί

TV-Mode setup
With the Dreambox remote control you have the possibility to control the dreambox and your tv device
with only one remote control. In order that your tv device reacts to the signals of the remote control, you
have to program it before.
There are 3 options for programming the rcu:
1. Programming with Code
2. Programming by Learning function
3. Programming by Scan function
Please read the steps of each programming method carefully, before you proceed.
Programming with Code
In this programming method a manufacturer-specific code is used (refer to device list on www.dreambox.de).
1. Press the OK-Button and the TV-Mode-Button for ˜ 3 seconds.
2. Enter the desired 3-digit Code 000-999 with the Numeric-Keypad. Now press the Mute- or Volume
Button in order to check if the tv device responds to the just entered code. If there is no response,
please try it with the next code from the list, according to the steps above.
3. If none of the given codes is suitable, please proceed with the chapter “Programming by Scan function”.
If no code is entered within 6 seconds or the TV-Mode-Button is pressed, the remote control will
exit the programming mode automatically.
Programming by Scan function
In this programming method the dreambox rcu sends every second another shutdown-code to the tv device,
until the tv shuts off. Use this method of programming, if the Programming with Code wasn’t successfully,
or the vendor of your specific tv device isn’t listed.
1. Press the OK-Button and the TV-Mode-Button for ˜ 3 seconds.
2. Enter 777 with the Numeric-Keypad, in order to start the scan mode and point the rcu (with
ir-sensor) into the direction of your tv device.
3. As soon as the tv device shuts down (Hint: Depending on the type of your tv device, this can last
some minutes), immediately press the OK-Button to store the current code and leave the scan-mode.
If no code is entered within 6 seconds or the TV-Mode-Button is pressed, the remote control will
exit the programming mode automatically.
Programming by Learning function
In this programming method the functions of the keys of your tv-remote control unit can adopted to the
dreambox rcu one-on-one. Only the DREAM- and the TV-Mode-Button couldn’t be programmed.
1. Press the OK-Button and the TV-Mode-Button for ˜ 3 seconds.
2. Enter 888 with the Numeric-Keypad, in order to start the Learning function.
3. Press the desired button on the dreambox rcu, (except the DREAM- and the TV-Mode-Button)
which you want to program.
4. Place the dreambox rcu and the tv-device rcu towards each other at a distance of ˜ 3-5 cm.
5. Press the desired button on the tv-device rcu for 2-3 seconds. Release this button, it is now programmed.
6. If you want to program another Button or you made a mistake during programming, just repeat this
process starting from step 3.
If no code is entered within 6 seconds or the TV-Mode-Button is pressed, the remote control will
exit the programming mode automatically.
Dreambox-Mode and TV-Mode
Dreambox-Modus
Press the DREAM-Mode-Button in order to activate the Dreambox-Mode in your rcu. Use the two
DIP-Switches in the battery compartment on the back, if you are going to use more than one dreambox in
a single room.
TV-Mode
By pressing the TV-Mode-Button the remote control unit switches to the tv-mode and the last stored
rcu-code is used. Now you can use the dreambox rcu instead of the tv-device rcu in order to control your
tv-device.
Duration of lighting of the Dreambox-Symbol
You can adjust (in seconds) the duration of how long the dreambox-symbol at the bottom is lit-up after you
once pressed a button on the rcu.
1. Press the OK-Button and the DREAM-Mode-Button for ˜ 3 seconds. The DREAM-Mode-
Button flashes 3 times.
2. Press one of the keys 0-9 on the Numeric-Keypad. 0 means “off”, 1-9 means the time in seconds.
Reset
1. Κρατάτε το κουμπί TV και το κουμπί OK μαζί για μερικα δευτερόλεπτα πιεσμένο, μεχρι το κουμπί TV να αναβοσβήσει.
2. Δινετε 999 στο τηλεκοντρόλ