Power of Dream HD+ Image for ET5000

[korn]

Online update Power of Dream HD+ Image for ET5000 13/09/2011

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update


Update of 13/09/2011

- Update routine Enigma2/Openembedded
- Added in the DLC picons OpenPlant

[korn]

Online update Power of Dream HD+ Image for ET5000 26/09/2011

Update drivers:

HDMI-CEC: address change signal with POLLPRI
sharpness-scaler: fixed 'neutral' value (middle of the scale)
-added video source viewport / clipping settings (/ proc / stb / VMPEG / [0-1] / clip_ *)

Update routine enigma2 ...

Note that sometimes the demo does not reboot itself at the end of the update, in this case to OFF / ON to interuptor

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

[korn]

Online update Power of Dream HD+ Image for ET5000 28/09/2011

et5000/et9000: Driver update

-tune speed improvements
-stc sync mode setting: /proc/stb/stc/[0,1]/sync
-dts audio ff/rewind/skip fix
-sci improvements
-timeshift detection (T/S vfd symbol)
-userspace timeshift symbol control (/proc/stb/lcd/symbol_timeshift, disables internal timeshift detection)
-fix pip with webbrowser combination

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

[korn]

Online update Power of Dream HD+ Image for ET5000 05/10/2011

- Modification of hypercam manager: the launch of enigmatic, verify that at least one local card is detected. If this is not the case, recovery hypercam. This should overcome the desire to hypercam etx000 on the launch.

- Changes introduced by OpenPlant etxx00 linux

-update routine Enigma2

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

[korn]

POD Image HD 2.1 ET5Χ00 02/02/2012

Update 02/02

- Update Manager map 2.18: support for HD channels on some maps csat.
- Provision in the DLC web interface OpenWeb: to install the current interface REMOVE BEFORE installing OpenWeb in plugins / extensions. Starting today PODHD the 'complete' automatically include OpenWeb instead of the old web interface after Dream.

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

[korn]

POD Image HD 2.2 ET5000 11/02/2012

[IMG]http://desmond.**************/Himg843/scaled.php?server=843&filename=infosk.jpg&res=medium[/IMG]

Update 11/02



New drivers AND
Passage Linux 3.2.2


changelog:
-added '/ proc / stb / video / videomode_preferred'
switch to linux-3.2.2


To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

[korn]

POD Image HD 2.2 ET5000 17/02/2012

[IMG]http://desmond.**************/Himg843/scaled.php?server=843&filename=infosk.jpg&res=medium[/IMG]

Update 17/02
- Added in the DLC's Valerie Project (http://code.google.com/p/project-valerie/)
To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

[korn]

POD Image HD 2.1 ET5000 26/03/2012 second update

Update 26/03

- mise à jour des drivers :
-DVB-T 5V
-make sci devices single-open
-improved tuner scan
-WMV support
-WMA support
-WAV support (pcm wrapped in PES, to keep sync with video)
-alsa mixer switch to enable/disable decoder audio
-internally control vfd symbols
-allow individual vfd symbol override from userspace
-frontend status: report correct FEC
-startup in 720p mode

Frontpanel:
-Add ET9x00 and ET6x00 wakeup button for new remote

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

[ilias]

POD Image HD 2.1 ET5000 10/04/2012

Update 10/04

- Update routine and Enigma2 Plugins

- Update of drivers:
DVB-T-5V
sci-make single-open devices
Improved scan-tuner
WMV-Support
WMA-media
Medium-WAV (pcm wrapped in polyester, to keep sync with video)
alsa-mixer switch to enable / disable audio decoder
Internally-vfd control symbols
Individual symbol vfd-allow override from userspace
-frontend status: Report correct FEC
-startup in 720p Mode

frontpanel:
-Add ET9x00 and ET6x00 new button for remote wakeup

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update

[korn]

POD Image HD 2.1 ET5000 19/04/2012

Update 19/04

-Routine update of enigma and plugins (which has a kernel rebuild due to change ntfs)
- Added plugin Airplay (streaming for iPhone / iPad, Extensions section of plugins)

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update